Free Articles on Family and Home and many other topics
Another free Family and Home article for you by William Lund
Titled: Supercharge Your Water Heater – Add a Hot Water Pump for Faster Hot Water! Get the Family and Home category RSS Feed

Supercharge Your Water Heater – Add a Hot Water Pump for Faster Hot Water!

Article Summary: Several types of hot water circulating systems are discussed and compared. By choosing the correct system for your needs you can benefit from faster hot water and be kind to the planet and environment at the same time.

We all do it. Run water down the drain while waiting for hot water. Who is going to jump into the shower when the water is freezing cold! Well no one. Is there a way to avoid running all of that water down the drain?

Yes. A hot water circulating system will eliminate the need to run that water down the drain. There are several types of hot water circulating systems available, and they are fairly easy to understand.

The first type of system is the full-time circulating system. In this type of system the hot water outlet of the water heater connects to a pipe that runs past each fixture in the home, and then back to the water heater. A small pump circulates the hot water through the pipe, thus there is always hot water near every fixture. Instant hot water!

But there is a price to pay! This is an expensive system to operate, since the pump consumes some energy and is running constantly; you have to pay for that energy. But far greater is the expense of heating the water. Heating water is very expensive, and so when you pump it through a long pipe, and the pipe is losing heat energy to the atmosphere around it, you end up spending a lot of money to heat the hot water piping and its immediate surroundings.

You can place the pump on a timer, so that during periods that people don’t normally use hot water, the pump is turned off. That helps, but it is still very expensive. Some systems also control the pump by monitoring the temperature of the water. The pump turns off when it reaches a set point, and then back on when the water drops to the lower set point. This reduces the energy consumption by the pump, but does little to reduce the far larger energy losses of the heat loss from the system.

Another problem with these systems is that they require a dedicated return line from the furthest fixture back to the water heater to function. This is an expensive option when building a home, and a far more expensive option to add on to an existing home.

There is another class of hot water circulating systems that do not require a return line. These systems use the cold water line as the return line. The cold water line always connects to the inlet of the water heater, so it will always work. There are a number of approaches being used for these cold water return type hot water circulating systems.

In some instances, for instance, where the water heater is lower than the rest of the system like in homes with a basement, a gravity type system can be used. Since hot water is less dense than cold water, the hot water rises up from the water heater to the fixtures and the cooled off hot water goes down the cold water return line back to the heater. A connection is required between the hot and cold water lines, and a valve that responds to temperatures is installed between them. Without a valve, the hot and cold water would always mix when you used either one.

Some systems use a pump connected between the hot and cold water lines with a built in valve, and as with the full time systems, some are operated via a timer, some are temperature controlled, and some use both methods.

Another type of system is known as a “hot water demand system”. With the demand type system, the user must push a button or utilize some other signal to start the pump, and then when hot water reaches the fixture, the pump shuts off.

The demand system is the lowest cost in terms of operating costs since it does not cause any more heat loss than if you just used the hot water fixture without the system. It only pumps when you “demand” hot water. Typically such systems use only $1 to $2 per year in electricity for running the pump.

You obtain your hot water more quickly than if you ran the faucet full blast, and you don’t wastefully run water down the drain. You’re happy and the environment is happy!

Article Source: http://www.upublish.info

About the Author:
William Lund
For more information about hot water heaters and circulating systems visit: Water Heaters And Circulating Systems Mr. Lund also has a website for information about Net Audio Ads: Lund One – Making Money Online