Free Articles on Computer and many other topics
Another free Computer article for you by David Picella
Titled: Dual Boot Windows and Linux: Single and Multiple Hard Drives Get the Computer category RSS Feed 
Dual Boot Windows and Linux: Single and Multiple Hard Drives
Article Summary: The technical side of the internet can be a frustrating place for a computer novice that is trying to get a simple job done. Finding clear instructions on how to setup a dual boot for Windows and Linux is next to impossible. This article presents simple dual boot instructions for Windows and Linux for both single and multiple hard drive configurations that actually work.
The internet is full of technical articles, many of which are way too complicated for the average computer user who just wants to solve a simple problem. If you pay close attention, the internet is also a place where the “gurus” spend a lot of time yelling for help in discussion boards and forums. So don’t feel bad, nobody has all the answers.
So you want to dual boot Windows and Linux on the same computer—it is really quite easy. I only have enough room here to tell you the most common way to do this on a single hard drive or using multiple hard drives. Obviously then, there are many ways to get the job done, but there are some critical things you should know. Let’s start with some critical information.
Windows and Linux: Same Hard Drive
The windows operating system MUST occupy the master boot record (MBR). Linux, on the other hand does not have to. In this scenario, you must install windows first! After Windows has been successfully installed, then you can install Linux. This is critical! The Linux “boot loader” is called GRUB. When you install Linux—MAKE SURE YOU DO NOT INSTALL THE LINUX BOOT LOADER TO THE MBR.
Configure the Windows Boot Loader: A Two Step Process
It is also possible to use GRUB to dual boot Windows and Linux on the same drive but this is a bit more complex—the Windows boot loader will get the job done. In the following commands, you will create a copy of the Linux boot sector and then save it in a file in the top level directory under Windows (C:\).
Step 1: Linux
From the shell in your Linux installation (boot from your installation disks):
Execute the following shell command, replacing /dev/hda3 with the location of your Linux boot partition.
shell# dd if=/dev/hda3 of=/bootsect.lnx bs=512 count=1
Copy the new file—bootsect.lnx—to a floppy disk and reboot to Windows.
Step 2: Windows
Copy bootsect.lnx to C:\ in Windows. Then execute the following command at the DOS prompt.
C:\> attrib -H -R -S \boot.ini
Edit boot.ini so that the first two lines are:
[boot loader]
timeout=30
After the last line, add:
c:\bootsect.lnx=“Start Linux”
That’s it, you are done! Reboot your machine and you will see a menu allowing you to select either Windows or Linux. Congratulations.
Windows and Linux: Two Hard Drives
This is also quite easy. In this case, you will boot to the Linux drive. We will add Windows to the Linux boot loader (i.e., GRUB). GRUB is my favorite boot loader.
Edit the /boot/grub/grub.conf file. One of the very first lines should contain:
timeout=30
After the last line add:
title Start Windows
map (hd1) (hd0)
map (hd0) (hd1)
rootnoverify (hd1,0)
makeactive
chainloader +1
Reboot your machine to the Linux drive and you will see a menu allowing you to select between Linux or Windows. Nice work!
This article is obviously short and does not include any explanations of how these commands work. There are variations on what I have shown here depending on your hardware setup, but I believe that these are the most common and should get the job done nicely. I would be happy to direct you to additional resources if this does not work for you.
Article Source: http://www.upublish.info
About the Author:
David Picella
David Picella is a Family Nurse Practitioner and PhD Student at UW Milwaukee who studies women's health issues and NaProTechnology. He also writes computer technical articles. You can find additional technical resources for this article in the technology section at: http://www.majella.us
