Free Articles on Certification and many other topics
Another free Certification article for you by Chris Bryant, CCIE #12933
Titled: Cisco CCNA 640-802 And CCENT Certification Exam Training: HDLC Configuration And Troubleshooting Get the Certification category RSS Feed

Cisco CCNA 640-802 And CCENT Certification Exam Training: HDLC Configuration And Troubleshooting

Article Summary: To earn your CCNA and CCENT certifications, you've got to master the basics of WAN links, HDLC, and PPP. In this installment of Chris Bryant's free CCNA / CCENT tutorial series, you'll learn how to configure and troubleshoot HDLC.

Your CCNA and CCENT exam success depends on knowing how to configure and troubleshoot HDLC and PPP on Cisco routers, as well as knowing the differences and similarities between the two. Today we'll take a look at HDLC and some basic router configurations, and in future CCNA and CCENT certification exam tutorials, we'll examine PPP in detail.

With a point-to-point WAN link such as the following, we've got two options for encapsulation - HDLC and PPP. (HDLC, PPP, and Frame Relay do not run on LANs - you wouldn't configure them on Ethernet interfaces.)

We're not going to discuss HDLC for long, since there's not much to say about it - but what there is to say is very important! The version of HDLC used by Cisco routers is the default encapsulation type on Serial interfaces, verifiable with the show interface serial command. (Only the portion of this command's output dealing with the PTP WAN link will be shown in this section.)

R1#show interface serial 1
Serial1 is up, line protocol is up
Hardware is HD64570
Internet address is 172.12.13.1/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set

R3#show int serial1
Serial1 is up, line protocol is up
Hardware is HD64570
Internet address is 172.12.13.3/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set


At this point, each partner in the PTP link can ping the other.

R1#ping 172.12.13.3

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.12.13.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms

R3#ping 172.12.13.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.12.13.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/35/36 ms

This particular version of the High Data-Link Control encapsulation is Cisco-proprietary, a fancy way of saying "only Cisco routers understand this encapsulation type". If a router at the end of a PTP link is running HDLC encapsulation, the remote partner in the link must do so as well.


If one of the routers is running another encapsulation type, the physical interfaces will still be up, but the line protocol will go down and IP connectivity will be lost. To illustrate, I'll change the encapsulation type on R3's Serial1 interface to the Point-To-Point Protocol (PPP).

R3(config-if)#exit
R3(config)#int serial 1
R3(config-if)#encapsulation ppp

A few seconds later, the line protocol goes down on R3.

2d04h: %SYS-5-CONFIG_I: Configured from console by console
2d04h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down

show interface serial 1 on both routers verifies that the physical interface is up, but the line protocol is down. IP connectivity is lost.

R3#show interface serial 1
Serial1 is up, line protocol is down

R3#ping 172.12.13.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.12.13.1, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)

R1#show interface serial 1
Serial1 is up, line protocol is down

R1#ping 172.12.13.3

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.12.13.3, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)

The encapsulation mismatch has brought the line protocol down, and to bring it back up, we simply need to make the encapsulation types match again. We'll do just that in the next installment of my exclusive Cisco CCENT / CCNA certification exam tutorial series!

Article Source: http://www.upublish.info

About the Author:
Chris Bryant, CCIE #12933
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free Cisco CCNA 640-802 certification exam study guides, CCNA 640-802 tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages. You can also visit his blog, which is updated several times daily with new Cisco certification articles, free tutorials, and daily CCNA / CCNP exam questions! For a FREE copy of his latest e-books, “How To Pass The CCNA” and “How To Pass The CCNP”, just visit the website! You can also get FREE CCNA and CCNP exam questions every day! Take the CCNA Mastermind Webinar Boot Camp with The Bryant Advantage!